How Deep Should a Patio Sub-Base Be? UK Guide
Share
How Deep Should a Patio Sub-Base Be?
It is one of the first questions every patio builder asks, and one of the most important to get right: how deep should a patio sub-base be? Dig too shallow and you risk sinking, rocking and cracked slabs within a couple of winters. Dig too deep and you waste money, time and a lot of effort carting away soil.
This guide gives you clear, practical depths for typical UK projects, explains how soil type, slab thickness and usage change the answer, and shows you how to work out your total dig-out depth from the finished level down.
The Short Answer
For a standard garden patio that will be walked on and used for furniture, the generally recommended sub-base depth is 100mm of compacted MOT Type 1. On softer ground, such as clay, or where heavier loads are expected, increase this to 150mm or more. For a driveway that will carry cars, a sub-base of 150 to 200mm or more is typically recommended.
That 100mm figure is the sub-base only. On top of it you will also need a bedding layer and the slab itself, so your total excavation depth will be considerably greater. We will work through that shortly.
What Is the Sub-Base and Why Does Depth Matter?
The sub-base is the compacted layer of crushed stone, usually MOT Type 1, that sits directly on the prepared ground under your bedding layer and paving. Its job is to spread loads, resist settlement and allow some water to drain away. If you want a deeper explanation of the material itself, read what MOT Type 1 is and why it is used under paving.
Depth matters because the sub-base is acting as a buffer between your slabs and the soil. A layer that is too thin cannot spread the load properly, so pressure concentrates on the soil underneath, which compresses and moves. The result is dips, tilting slabs and cracked joints. The softer the ground and the heavier the use, the more depth you need.
Recommended Sub-Base Depths by Project
Garden Patios and Seating Areas
For typical domestic patios on reasonably firm ground, 100mm of compacted Type 1 is a sound standard. Many landscapers go to 125mm or 150mm as cheap insurance, particularly with larger format slabs.
Garden Paths and Walkways
Light-use paths for foot traffic can sometimes go slightly thinner, around 75 to 100mm, on firm, well-drained soil. If the path crosses soft or shaded, damp ground, treat it like a patio and go to 100mm or beyond.
Soft Ground and Clay Soil
Clay holds water, swells in winter and shrinks in dry summers, so it moves more than sandy or loamy soil. In these conditions, plan for 150mm or more of compacted sub-base, and consider laying a geotextile membrane over the soil first to stop the stone mixing with the clay. Very soft or boggy spots may need to be dug out further and replaced with compacted aggregate.
Driveways and Vehicle Areas
Cars put far more stress on paving than feet. For driveways, 150 to 200mm is a typical minimum, with deeper or reinforced builds for heavier vehicles or poor ground. For vehicle areas, thickness of the slabs and the bedding method also change, so check the manufacturer's guidance and read our guide to 20mm paving slabs and their suitability.
Light Use: Stepping Stones and Decorative Areas
Small stepping stones, edging or purely decorative spots may only need 50 to 75mm, but keep in mind that thin bases have little tolerance for movement.
How to Calculate Your Total Dig-Out Depth
This is where many first-time builders get caught out. The depth of your hole needs to account for every layer. Use this simple formula:
Total dig depth = sub-base depth + bedding layer depth + slab thickness
Here is a typical example for a garden patio using 20mm porcelain slabs:
- Compacted Type 1 sub-base: 100mm
- Mortar bedding layer: around 30 to 40mm
- Slab thickness: 20mm
- Total excavation: approximately 150 to 160mm
And one for a patio on clay using 22mm sandstone:
- Compacted Type 1 sub-base: 150mm
- Mortar bedding layer: around 40mm
- Slab thickness: about 22mm
- Total excavation: approximately 210mm
Always check the actual thickness of the slabs you are buying, as it varies between products. Our size and thickness guide and article on paving slab sizes explained are useful references.
Where Should the Finished Surface Sit?
Your dig-out depth is measured from your intended finished level, and that level needs careful thought. There are two key rules.
Keep it below the damp-proof course. Where the patio meets your house, the finished paved surface should sit at least 150mm below the damp-proof course (DPC), and ideally below any air bricks, to prevent moisture bridging into the walls. If the existing ground level is too high to achieve this, you may need to lower it or install drainage.
Allow for a fall away from the house. Your patio should slope gently away from the building so rainwater runs off. This means your depth will vary slightly across the area, being shallower at the house side and deeper at the far edge, or the reverse depending on your design. We explain how much fall to use in our guide to the correct patio drainage gradient, and our drainage guide covers wider water management.
How Soil Type Affects Depth
- Sandy or gravelly soil: drains freely and is usually stable. The standard 100mm often suffices.
- Loam: a good, balanced soil, but check for soft pockets and topsoil. Remove all topsoil down to firm subsoil.
- Clay: prone to movement and waterlogging. Go deeper, use membrane and ensure good drainage.
- Made ground or backfill: near new builds or old structures, ground can be uneven and poorly compacted. Dig out and replace soft material.
- Peaty or boggy soil: unsuitable for shallow builds. Seek specialist advice.
A simple test: dig a trial hole. If you can easily push a spade into the base of the dig-out, the ground is soft and needs more depth or reinforcement.
Building the Sub-Base Properly
Depth alone will not save a badly built base. Follow these principles:
- Remove all topsoil, roots and organic matter. These rot and shrink, causing settlement.
- Compact the exposed subsoil with a plate compactor before adding stone.
- Add Type 1 in layers of 75 to 100mm, compacting each layer separately. A single deep layer cannot be compacted properly.
- Lightly dampen the aggregate if it is very dry, as a little moisture helps it bind.
- Check levels and falls repeatedly with string lines and a spirit level.
For the whole process from start to finish, follow our guide on how to lay paving slabs in your garden.
Does Slab Type Affect Sub-Base Depth?
The sub-base depth is largely driven by ground and loads, but slab choice has an influence. Thin or large-format slabs are less forgiving of an uneven or weak base, since they need uniform support across their whole surface. Porcelain, for example, is extremely hard but needs full bedding to avoid hollow spots. Natural stone like Indian sandstone is thicker and heavier, which can slightly mask minor imperfections but also needs a firm base.
If you are still choosing slabs, compare the materials in porcelain vs Indian sandstone for UK patios and porcelain paving vs concrete, and browse our porcelain paving and Indian sandstone collections. Large formats are covered in our large-format paving slab guide.
What Happens If the Sub-Base Is Too Shallow?
- Slabs sink or tilt where furniture or foot traffic is concentrated
- Joints open up and fill with weeds or water
- Surface water pools in dips. Read how to stop water pooling on a patio
- Frost and moisture can heave sections of paving out of level, as explained in is porcelain paving frost resistant?
- Slabs crack, particularly on edges and corners
Fixing these problems later means lifting and relaying, which costs far more than digging a little deeper at the start.
Planning Quantities and Budget
Once you know your depth, you can calculate how much aggregate you need. Our guide how much MOT Type 1 do I need for a patio? walks you through it with worked examples. Pair it with our guides to calculating square metreage and estimating the number of slabs, and check how much paving slabs cost in the UK to set your budget.
Frequently Asked Questions
Is 50mm of sub-base enough for a patio?
Generally no. Fifty millimetres is too thin for most patios and offers little protection against movement. Aim for at least 100mm for any area used regularly.
Can I lay slabs directly on soil?
This is strongly discouraged. Soil moves, holds water and cannot support slabs evenly, so paving laid this way tends to sink and crack.
Do I need a deeper base for porcelain paving?
Not necessarily deeper, but it must be even, well compacted and well drained. Porcelain needs full, uniform support and the correct bonding method.
How deep should the sub-base be for a shed base or hot tub?
Heavy loads call for a deeper, stronger base. Seek professional advice, as a hot tub in particular may need a reinforced concrete slab.
Final Thoughts
For most UK garden patios, 100mm of compacted MOT Type 1 is the standard, with 150mm or more for clay, soft ground or heavier use, and 150 to 200mm for driveways. Add in your bedding and slab thickness to find your total dig depth, and always build up the sub-base in compacted layers. Do this and your slabs, whether EC Grey porcelain or Mint Fossil sandstone, will stay level for many years.
Questions about your project? Get in touch with our team or browse our patio slabs for inspiration.