What Is MOT Type 1 and Why Is It Used Under Paving?
Share
What Is MOT Type 1 and Why Is It Used Under Paving?
Ask any landscaper what makes the difference between a patio that stays flat for twenty years and one that is wobbling after two, and you will hear the same answer: the base. And when it comes to the base, the material most UK professionals reach for is MOT Type 1. If you are planning your own patio and keep seeing the term in guides and merchants' price lists, this article explains exactly what it is, why it is used under paving, and how to get the best from it.
What Is MOT Type 1?
MOT Type 1 is a graded crushed-stone aggregate used to form a compacted sub-base beneath paving, driveways, paths and roads. It is typically made from crushed rock such as limestone, granite or slate, or from recycled materials like crushed concrete and brick, which are processed to a set particle-size range.
The name causes a lot of confusion. It has nothing to do with your car's annual MOT test. It comes from the Ministry of Transport, the former government department that originally set out the specification for road-building materials. Today the standard is maintained within the highways specification used across the UK, but the old name has stuck, and you will still see it called "MOT Type 1", "Type 1 sub-base" or simply "Type 1" at builders' merchants and aggregate suppliers.
Type 1 is a mix of particles ranging from larger stones, typically up to around 40mm, down to fine dust. It is this deliberate mix of sizes, rather than the stone itself, that gives it its useful properties.
Why Is the Mix of Sizes So Important?
Picture a bucket full of marbles of the same size. There are gaps between every marble, and the pile will shift and settle under pressure. Now picture a bucket filled with a mixture of large stones, medium chippings, grit and dust. The smaller pieces fill the voids between the larger ones, and when you compact the mixture it locks together into a dense, interlocking mass.
That is exactly what happens when you compact Type 1 with a plate compactor. The angular, crushed edges of the stones grip one another, creating a firm, stable layer that spreads loads evenly and resists movement. Because it is angular rather than rounded, it holds together far better than something like pea gravel or sharp sand alone.
Why Use MOT Type 1 Under Paving?
A paved surface is only as good as what is underneath it. Slabs sit on a thin bedding layer, and that bedding layer needs a stable foundation. Type 1 provides it in several ways.
1. It Creates a Stable, Load-Spreading Foundation
Once compacted, Type 1 distributes the weight of people, furniture, planters and occasionally vehicles across a wider area of soil underneath. This prevents slabs from sinking, tilting or cracking as individual points come under pressure. This matters even more with premium slabs, such as 20mm porcelain, which need full, even support to perform properly. Our guide to 20mm paving slabs and their suitability explains why.
2. It Helps Water Drain Away
Type 1 is open enough to let water pass through it, yet dense enough to remain stable. Water that seeps through joints or around the edges of the patio can drain down into the ground instead of sitting under your slabs. This is particularly important in the UK, where saturated ground and freeze-thaw cycles can heave poorly drained paving out of level. See how this relates to winter performance in is porcelain paving frost resistant?
3. It Reduces Settlement Over Time
Soil naturally moves. It shrinks and swells with moisture, it settles after digging, and it can be softened by water. A compacted Type 1 layer acts as a buffer between that moving ground and your finished surface, helping the patio stay level and the joints stay tight.
4. It Gives You a Firm Surface to Set Falls
Because a compacted sub-base is stable, you can shape it to create the gentle fall that carries rainwater away from your house. Getting this right at base level is far easier than trying to correct it later with a thick bedding layer. We cover this in detail in our guide to the correct patio drainage gradient.
5. It Is Cost-Effective and Widely Available
Type 1 is inexpensive compared with the cost of replacing a failed patio, and you can buy it from builders' merchants, aggregate suppliers and many garden centres, either loose by the tonne or in bulk bags. It is also very forgiving to work with, which is one reason it is popular with both professionals and DIYers.
MOT Type 1 vs Other Base Materials
Type 1 is not the only possible sub-base, so it helps to see how it compares.
- Hardcore or broken brick: a traditional option, but the material is inconsistent. It has large voids and does not compact as tightly unless blinded with finer material.
- Sharp sand: good for bedding layers but unsuitable as a sole sub-base because it can wash out and does not lock together the way crushed stone does.
- Crushed concrete or recycled aggregate: perfectly good when it is graded to the Type 1 specification, and often more environmentally friendly.
- Type 3 or single-size stone: permeable and useful for specific drainage applications, such as permeable paving, but not a direct substitute for Type 1 in a standard patio.
For a standard residential patio or path, MOT Type 1 remains the go-to choice for good reason.
How Is Type 1 Used Under a Patio?
A typical patio build has three layers: the compacted sub-base, a bedding layer and the paving itself. Here is how the Type 1 stage fits in.
- Mark out and excavate. Dig out enough depth to take the sub-base, bedding layer and slab thickness, with the finished surface sitting below the damp-proof course of the house. Our guide to how deep a patio sub-base should be works through the numbers.
- Compact the soil. Firm the exposed ground with a plate compactor. Remove any soft spots, roots or organic matter, and consider a geotextile membrane over soft or clay soils.
- Add Type 1 in layers. Spread the material in layers of no more than about 75 to 100mm at a time, compacting each one thoroughly before adding the next.
- Set the falls. Shape and check the surface to achieve your drainage gradient as you go, using string lines and a spirit level.
- Add the bedding layer. Spread a mortar bed or bedding mix over the compacted Type 1 and lay your slabs.
- Joint and finish. Fill the joints with a suitable jointing compound.
For more on the full process, read our practical guide to how to lay paving slabs in your garden.
How Much Type 1 Do You Need?
The amount of Type 1 you need depends on your patio area, the depth of the sub-base and an allowance for compaction. As a rough guide, compacted Type 1 weighs a little over two tonnes per cubic metre, and loose material needs to be ordered with an allowance for the volume it loses when compacted. We have written a full walkthrough with worked examples in how much MOT Type 1 do I need for a patio? You can combine it with our guides to calculating square metreage and estimating the number of paving slabs to plan your entire order.
Common Mistakes When Using MOT Type 1
- Skipping compaction. Raking Type 1 flat and walking on it is not enough. You need a plate compactor, or a hired compactor for larger areas.
- Laying it too thickly in one go. A deep single layer cannot be compacted all the way down and will settle later.
- Ignoring drainage. A perfectly compacted base that has no fall will still hold water on the surface. Learn how to stop water pooling on a patio.
- Laying slabs on dry sand alone. Without a proper sub-base, paving will move, particularly in wet conditions.
- Working in very wet conditions. Over-saturated Type 1 will not compact well. A little moisture helps compaction, but sodden material does not.
Does Paving Material Affect the Sub-Base You Need?
The sub-base principles are the same whichever paving you choose, but the finish on top can influence your approach. Dense porcelain, which absorbs almost no water, relies heavily on a stable, well-drained base and correct bonding, because water has nowhere to go but along the surface and through the joints. Natural stone such as Indian sandstone can tolerate a little more variation but will still sink or rock on a poor base. Concrete flags are more forgiving of small movement but crack if the base fails.
Whichever you choose, the base matters. Compare materials in porcelain vs Indian sandstone for UK patios, porcelain vs concrete and porcelain vs natural stone, then explore our porcelain paving, Indian sandstone and patio slabs collections.
Do You Need Type 1 for Every Project?
For almost any paved area that people will walk or sit on, a compacted Type 1 sub-base is recommended, and for heavier loads it becomes essential. Driveways need a deeper, stronger build, while light-use stepping-stone paths may get away with a thinner base. As a rule, if in doubt, go deeper. Our UK guidelines page sets out the standards we recommend for domestic paving, and our drainage guide covers falls and water management.
Frequently Asked Questions
Is MOT Type 1 the same as hardcore?
No. Hardcore is a general term for rubble and broken material. MOT Type 1 is a graded, crushed aggregate with a defined particle-size range that compacts into a dense, stable layer.
Can I use MOT Type 1 on its own under paving?
Type 1 forms the sub-base. It is then topped with a bedding layer, typically mortar, and your paving slabs. It is not laid directly under slabs as the only layer.
Does MOT Type 1 drain water?
It allows water to pass through slowly but is not a free-draining material like clean single-size stone. For heavy-water sites, you may need extra drainage measures.
Final Thoughts
MOT Type 1 is the unsung hero of every successful patio. It is inexpensive, easy to source and, when properly compacted in layers, gives your paving the firm, level, well-drained foundation it needs to last. Whether you are laying Dome Grey porcelain, Kandla Grey Indian sandstone or any other slab from our paving slabs range, a good base is the best investment you can make.
Planning your project and want a second opinion? Contact our team and we will be happy to help.